Scramrod Assembly Guide

Featured

Written By: Zack Freedman
  • Comments: 0
  • Favorites: 0

Featured Guide

Difficulty

Easy

Steps

6

Time Required

00:05:00

Sections

1

Flags

2

In Progress

In Progress

This guide is currently being written. Reload periodically to see the latest changes.

Featured Guide

Featured Guide

This guide has been found to be exceptionally cool by the site's staff.

Introduction

Thanks for buying a Voidstar Combat Sports Scramrod! Whether your platform is belt or MOLLE, this guide will show you how to build the only collapsible ramrod for Nerfing.

  1. Let's take inventory. Your Scramrod includes:

    • Let's take inventory. Your Scramrod includes:

    • Handle segment and end segment

    • Five middle segments

    • Case, either MOLLE or belt-mounted. This guide uses a belt-mounted case, but the instructions are the same for MOLLE.

    • Toggle and endcaps

    • 12" shock cord

    • 24" shock cord

    • If you'd like to install the endcaps for a tidier appearance, you'll also need some glue like Zap-a-Gap or E-6000. Gorilla Glue won't work.

    Edit

  2. Thread the 24" cord through the handle. Tie a single knot as close to the end as possible, and pull it tight. Tuck the free end of the knot into the handle and pull the entire knot into the handle.

    • Thread the 24" cord through the handle.

    • Tie a single knot as close to the end as possible, and pull it tight.

    • Tuck the free end of the knot into the handle and pull the entire knot into the handle.

    • Don't pull too hard - you can break the handle. You may want to use a screwdriver or something to gently press it in.

    • Thread the five rod segments onto the cord. All five have spikes on both ends.

    Edit

  3. Pull the cord nice and tight. Pinch and hold the cord where it leaves the rod segment. Thread the end segment onto the cord. Note that the cord should poke out of the blunt end, not the spiky end.

    • Pull the cord nice and tight.

    • Pinch and hold the cord where it leaves the rod segment.

    • Thread the end segment onto the cord. Note that the cord should poke out of the blunt end, not the spiky end.

    • Tie a single knot on the cord as close to the end as possible, and pull it tight.

    Edit

  4. Tuck the exposed ends of the cord into the segments. Gently push the knots in with a screwdriver or something. If desired, glue the endcaps over the exposed ends, and allow the glue to dry. These aren't necessary, but they look neat. Fold the Scramrod up and nest the segments into the handle.

    • Tuck the exposed ends of the cord into the segments. Gently push the knots in with a screwdriver or something.

    • If desired, glue the endcaps over the exposed ends, and allow the glue to dry. These aren't necessary, but they look neat.

    • Fold the Scramrod up and nest the segments into the handle.

    Edit

  5. Thread the toggle onto the 12" shock cord. Thread each end of the shock cord through the holes in the handle. Note the orientation! Tie the exposed ends in a loose square knot. Don't tighten it yet!

    • Thread the toggle onto the 12" shock cord.

    • Thread each end of the shock cord through the holes in the handle. Note the orientation!

    • Tie the exposed ends in a loose square knot. Don't tighten it yet!

    Edit

  6. Insert the ramrod into the case and put the toggle flat against the bottom. Tighten the knot so the ramrod is held securely, but the toggle is easy to pull away.

    • Insert the ramrod into the case and put the toggle flat against the bottom.

    • Tighten the knot so the ramrod is held securely, but the toggle is easy to pull away.

    • You're done! Go clear some jams!

    Edit
Conclusion

Thanks for buying, and building, a Voidstar Combat Sports Scramrod! Nerf on!

Author

Zack Freedman

Member since: 08/28/2019

1,109 Reputation

4 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 3

Past 30 Days: 14

All Time: 839